Quelltext der Seite Vencube in conjunction with HVMC-100 vending machine control

==Operating the Vencube with a Höfer HVMC-100 vending machine control==

===Requirements===

For MDB operation of the Vencube with an HVMC controller, the use of an EPROM with the software version: <br />
<code>HVMC 100-CC Version 1.38EUR (2Mbit)</code><br />
is mandatory! EPROMs larger than 1Mbit cannot be used in the first series of HVMC controllers; for this reason, only a BDV Vencube can be used. All subsequent HVMC controllers are equipped for MDB operation with a Vencube after a software update. These controllers can be distinguished by the printed labels.

===HVMC 100===

{| class="wikitable" border="1"
|-
|[[Datei:HVMC_100_Beschriftung.jpg|250px|]]
| style="text-align:center" |
'''Print: HVMC 100:'''<br />
<br />
Vencube can only be connected under BDV!
|}

===HVMC 100-1/-2/-3===

{| class="wikitable" border="1"
|-
|[[Datei:HVMC_100-1_Beschriftung.jpg|250px|]]
|[[Datei:HVMC_100-2_Beschriftung.jpg|250px|]]
|[[Datei:HVMC_100-3_Beschriftung.jpg|250px|]]
|-
| colspan="3" style="text-align:center" |
'''Print: HVMC 100-1/-2/-3'''<br />
<br />
MDB operation with a Vencube is possible after a software update!
|}

*Software version <code>HVMC 100 Version 1.38 EUR</code> must be used.
*Convert the controller to MDB operation: →Set DIP switch 2 to OPEN.
*Set <code>C8.A with Display Card Amount</code> in the menu.

After replacing the EPROM, the controller must be initialized and reconfigured. All previous data will be lost.

==Connecting the Vencube with the MDB Interface==

===Preparation===

#Disconnect the vending machine control system from the power supply (press the main switch or disconnect ST7).
#Check the EPROM version:<br><code>HVMC 100-CC Version 1.00</code> must be replaced with<br><code>HVMC 100-CC Version 1.38</code>!<br>Note the installation direction; the notch on the EPROM and IC socket is important, not the EPROM sticker.
#Insert the Vencube into the MDB interface of the control system.
#Connect MDB payment systems to the Vencube via MDB.
#Turn on the vending machine.

===Initialize the controller===

#The following display should now appear:<br><code>EPROM swap -> Initialize!</code>
#Set DIP switches 1 and 5 to the edge of the board and 2-4 to OPEN (controller initialization)!
#Press the star button
#The following will appear on the LCD: <code>Clear ??</code>
#Now press selection button 5 on the machine.
#Now set all DIP switches to OPEN again.
#Wait until the display shows <code>Help! F6</code>.
#Either continue with the section [[Vencube in conjunction with HVMC-100 vending machine control#Switching to a two-line display|'''"Switching to a two-line display"''']] or continue with the section [[Vencube in conjunction with HVMC-100 vending machine control#Switching to MDB mode|'''"Switching to MDB mode"''']].

===Switching to a two-line display===

#If a two-line display is installed, the display setting must be changed to 2 lines with 16 characters.<br>'''Important:''' With a single-line LCD display, this step can be skipped!
#Press the star button for more than 5 seconds: <br><code>Clr ERR!</code> appears (continue to hold)<br>and wait for the <code>ServMenu</code> display and release.<br>Following: <code>C 0. .</code>
#Press selection button 2: You will be asked for a password! <code>PW ????</code><br>The password is 4231, press the respective selection buttons and after entering it, the following appears: <code>C 1. .</code>
#Press selection button 4 and press selection button 2 several times to go to the menu item <code>C 1.C.</code>.
#Use selection key 4 to call up the setting <code>1Zl.8St.</code><br>and use selection key 2 to set it to two lines. <code>2Zl.16St</code>
#Use selection key 1 to go back until <code>C 0. .</code> appears on the display.
#Press the star key
#Wait until <code>Help! F6</code> appears on the display.

===Switch to MDB operation===

#Activate the MDB credit system: Set DIP switches 1 and 3-5 to OPEN and DIP switch 2 to the board edge.
#If necessary, activate the blank lamp control for GP: Set DIP switch 4 to the board edge as well.
#Press the star button<br>After the controller has booted up, one of the two displays should appear.<br>Either: <code>No change!</code> or: <code>Hello</code>

===Setting the machine===

#Press the star button for more than 5 seconds:<br><code>Clr ERR!</code> appears (continue to hold)<br>and wait for the <code>ServMenu</code> display and release.<br>Following: <code>C 0. .</code>
#Press selection button 2: You will be asked for a password! <code>PW ????</code><br>Password is 4231, press the corresponding selection keys and after entering the following appears: <code>C 1. . </code>
#Now configure the machine in the following menu items:
##<code>C1.3 </code> Set the date and time
##<code>C1.6 </code> Specify the number of slots
##<code>C1.1 </code> Assign the selection keys to the outputs
##<code>C6 </code> Price setting
##'''Important!:''' <code>C8 </code> Set the credit system setting in menu item <code>C8.A</code> to "display with card amount"!
#Use key 1 to menu item <code>C 0. . </code>
#Press the star button.
#Turn off the machine, wait a few seconds, and turn it back on.
#Test the sale.


[[Category:Index]]
[[Category:Instructions]]
[[Category:Sielaff]]
[[Category:Vendo]]