Canto: Unterschied zwischen den Versionen

Aus Vensolutions
Zur Navigation springen Zur Suche springen
VisuellWikitext
Keine Bearbeitungszusammenfassung
Zeile 5: Zeile 5:
{{Vorlage:Vencube Montage und Inbetriebnahme}}
{{Vorlage:Vencube Montage und Inbetriebnahme}}


 
== Problem solving  ==
{|
| style="vertical-align:top; width:40em"|
*VenCube möglichst in der Nähe der Automatensteuerung und den Zahlungssystemen platzieren.
*Bodenplatte im Automaten verkleben, oder verschrauben. Falls die Bodenplatte Verklebt wird, bitte ohne Vencube die Bodenplatte fest andrücken.
*Automat spannungsfrei schalten und alle vorhandenen Zahlungssysteme von der Automatensteuerung trennen.
*MDB-Master Anschluss vom VenCube mit der Steuerung verbinden.
*MDB-Slave Anschluss mit allen vorhandenen Zahlungssystemen verbinden. Für zusätzliche MDB-Slave Anschlüsse sollten Y-Kabel genutzt werden.
*Türschalter einbauen.
{{Vorlage:Hinweis vorhandener Türschalter}}
{{Vorlage:Hinweis Türschalter als Schließer}}
| style="vertical-align:top"|
 
| style="vertical-align:top"|
 
|
|}
 
==Problemlösungen==


{| class="wikitable" border="1"
{| class="wikitable" border="1"
|-
|-
! Automatenvariante
! Vending machine variant
! Software
! Firmware
! Fehlerbild
! Error image
! Abhilfe
! Rectification
|-
|-
| Dual Coup
| Dual Coup
| Canto Rev.  1.6  DC / Kontrollplatine Rev. 1.6 DC
| Canto Rev.  1.6  DC / Kontrollplatine Rev. 1.6 DC
|
|
*Nach einem fehlerhaften Verkauf nimmt der VenCube Geld an, der Kredit wird jedoch nicht im Automatendisplay angezeigt und es ist kein weiterer Verkauf möglich.
*After an incorrect sale, the Vencube accepts money, but the credit is not shown on the machine display and no further sale is possible.
*Erst nach einem Automatenneustart wird wieder Kredit im Automatendisplay angezeigt und Verkäufe sind möglich.
*Only after restarting the machine is credit shown on the machine display again and sales are possible.
|
|
*Im VenCube MDB-Level 2 auf MDB-Level 1 umstellen.
*Change MDB level 2 to MDB level 1 in the VenCube.  
|-
|-
|}   
|}   

Version vom 18. Januar 2022, 12:54 Uhr

Installation instructions

File User manual Vencube beta currently only in German
Download link BA_Vencube_beta_032020.pdf

Vencube assembly and commissioning

Mount the Vencube

The device is assembled by the customer.
Proceed as follows during assembly:

  • Open the machine.
  • Turn off the power to the machine.
  • Determine the optimal installation position:
    Place the VENCUBE as close as possible to the machine controls and payment systems.
    Make sure that the controls are easily accessible.
    Note the cable length.
  • Glue the base plate (holder) and screw it. (Image 1)

If gluing is not possible, the assembly click holder must be screwed diagonally to the designated points in the machine with at least 2 screws1). The screw heads must be complete Sit flush and must not protrude.
1) Hardened countersunk self-drilling screw, ∅ 3.5 according to DIN 7504

  • Clip the VENCUBE into the base plate. (Image 2)
  • Remove the machine controls cover.

The machine must be voltage-free!

  • Disconnect all existing payment systems (1, 2) from the machine control. (Image 3)
  • Connect the cables from the VENCUBE:
  • Connect the (MDB) master connection (3) from the VENCUBE to the vending machine control. (Image 4)
  • Connect the (MDB) slave port (4) to all existing payment systems (5). If necessary, use a Y-cable. (Image 5)
  • If possible, glue the antenna (6) behind a plastic cover. (Image 6)
  • Route the antenna cable.
  • Lay all cables professionally with cable ties.

Never use the existing door switch of the machine, this can destroy the Vencube.

Always connect the door switch as closer to plug 1 with the Vencube.
Use connector "COM" and connector "NO" from the switch.

Image 1
Image 3
Image 5
Image 2
Image 4
Image 6

Vencube Commissioning

  • Turn on the machine.
  • If necessary, adjust the Vencube using the Ventool.
  • If necessary, configure the machine control and the payment systems.
    You can find information on this in the wiki!
  • Wait until both LEDs turn green.
  • Close the door.
  • Test the machine by making a trial vend with change.
  • Open the door again.
  • Enter the data for VENSOFT (serial number, machine number).
  • Perform a cash withdrawal by pressing the “E” button on the Vencube until you hear a beep.
  • Close the door.
  • Commissioning is complete.

Problem solving

Vending machine variant Firmware Error image Rectification
Dual Coup Canto Rev. 1.6 DC / Kontrollplatine Rev. 1.6 DC
  • After an incorrect sale, the Vencube accepts money, but the credit is not shown on the machine display and no further sale is possible.
  • Only after restarting the machine is credit shown on the machine display again and sales are possible.
  • Change MDB level 2 to MDB level 1 in the VenCube.
Abgerufen von „https://wiki.vensoft.de/en/index.php?title=Canto&oldid=4927“