Robimat

Back to Sielaff overview

Installation instructions

File	User manual Vencube beta currently only in German
Download link	BA_Vencube_beta_032020.pdf

Vencube assembly and commissioning

Mount the Vencube

The device is assembled by the customer. Proceed as follows during assembly: Open the machine. Turn off the power to the machine. Determine the optimal installation position: Place the VENCUBE as close as possible to the machine controls and payment systems. Make sure that the controls are easily accessible. Note the cable length. Glue the base plate (holder) and screw it. (Image 1) If gluing is not possible, the assembly click holder must be screwed diagonally to the designated points in the machine with at least 2 screws1). The screw heads must be complete Sit flush and must not protrude. 1) Hardened countersunk self-drilling screw, ∅ 3.5 according to DIN 7504 Clip the VENCUBE into the base plate. (Image 2) Remove the machine controls cover. The machine must be voltage-free! Disconnect all existing payment systems (1, 2) from the machine control. (Image 3) Connect the cables from the VENCUBE: Connect the (MDB) master connection (3) from the VENCUBE to the vending machine control. (Image 4) Connect the (MDB) slave port (4) to all existing payment systems (5). If necessary, use a Y-cable. (Image 5) If possible, glue the antenna (6) behind a plastic cover. (Image 6) Route the antenna cable. Lay all cables professionally with cable ties. Never use the existing door switch of the machine, this can destroy the Vencube. Always connect the door switch as closer to plug 1 with the Vencube. Use connector "COM" and connector "NO" from the switch.

Image 1 Image 3 Image 5

Image 2 Image 4 Image 6

Vencube Commissioning

• Turn on the machine.
• If necessary, adjust the Vencube using the Ventool.
• If necessary, configure the machine control and the payment systems.
  You can find information on this in the wiki!
• Wait until both LEDs turn green.
• Close the door.
• Test the machine by making a trial vend with change.
• Open the door again.
• Enter the data for VENSOFT (serial number, machine number).
• Perform a cash withdrawal by pressing the “E” button on the Vencube until you hear a beep.
• Close the door.
• Commissioning is complete.

Installation location of the Vencube Door switch angle Door switch angle with switch

Built-in door switch angle Screwed angle door switch

Initial commissioning

After the VMC is switched on for the first time with the Vencube connected, there is increased data exchange between the controller and the Vencube. As a result, the VMC cannot be operated for up to ten minutes, or only very slowly, and coin acceptance and payout can be disrupted at the same time. After the waiting time, the machine will work again without any problems.

Settings of the VMC

Set selections in cashles menu to "Hex Format", then selections are equal to the product code

VMC Auster SUE

Make the following settings in the patch menu and check them in the installation menu and make additional settings there if necessary.

The patch menu is reached via the service menu (M-8-E) by entering 99M 55M.

Einstellungen im Patchmenü M - 8 - E 99M 55M Menüstruktur wie in Einstellung Option ALT.PAYOUT enabled TUBECOUNT Coin Mech contr. MIXED PAYMENT allowed MDB-comp.mode B.Pract. SAVE SETTINGS yes Nach betätigen der "E"-Taste steht "done" als Bestätigung im Display!

Einstellungen im Installationsmenü M - 7 - E Menüstruktur wie in Einstellung Option > KREDITSYSTEM KRED.KONFIG. MAN.EINSTELLEN > GELDWECHSLER TUBENZÄHLER Münzwechsler ALT. PAYOUT ein TUBENLEERMELDUNG ggf. Anpassen > KARTENSYSTEM MISCHZAHLUNG ein MIXED PAYM.PRICE Barpreisliste MDB-comp.mode Best Practice MDB ITEM NUMBERS Hexadezimal

Softwarestand / FTL

Anzeige des Softwarestandes im Servicemenü: M - 8 - E - 21 - L

Was steckt hinter der Softwarebezeichnung?

Software	Patchmenü	FTL geeignet

VMC Auster SUE M32

Make the following settings in the patch menu and check them in the installation menu and make additional settings there if necessary.

The patch menu is reached via the service menu (M-8-E) by entering 99M 55M.

Einstellungen im Patchmenü M - 8 - E 99M 55M Menüstruktur wie in Einstellung Option ALT.PAYOUT enabled TUBECOUNT Coin Mech contr. MIXED PAYMENT allowed MDB-comp.mode B.Pract. SAVE SETTINGS yes Nach betätigen der "E"-Taste steht "done" als Bestätigung im Display!

Einstellungen im Installationsmenü M - 7 - E Menüstruktur wie in Einstellung Option > KREDITSYSTEM KRED.KONFIG. MAN.EINSTELLEN > GELDWECHSLER TUBENZÄHLER Münzwechsler ALT. PAYOUT ein TUBENLEERMELDUNG ggf. Anpassen > KARTENSYSTEM MISCHZAHLUNG ein MIXED PAYM.PRICE Barpreisliste MDB-comp.mode Best Practice MDB ITEM NUMBERS Hexadezimal

Softwarestand / FTL

Anzeige des Softwarestandes im Servicemenü: M - 8 - E - 21 - L

Was steckt hinter der Softwarebezeichnung?

Software	Patchmenü	FTL geeignet

Problemlösungen

Übersicht der Problemlösungen

• Bei Sielaff Automaten erscheint „Bitte Warten“ im Automaten Display und es ist kein Verkauf möglich.
• Der Automat gibt kein Wechselgeld aus.
• Keine Münzannahme und keine Wechselgeld Ausgabe bei Sielaff Automaten.