Vencube in conjunction with HVMC-100 vending machine control

Operating the Vencube with a Höfer HVMC-100 Controller

Requirements

For MDB operation of the Vencube with an HVMC controller, the use of an EPROM with the software version:
HVMC 100-CC Version 1.38EUR (2Mbit)
is mandatory! EPROMs larger than 1Mbit cannot be used in the first series of HVMC controllers; for this reason, only a BDV Vencube can be used. All subsequent HVMC controllers are equipped for MDB operation with a Vencube after a software update. These controllers can be distinguished by the printed labels.

HVMC 100

Datei:HVMC 100 Inscription.jpg

Print: HVMC 100: Vencube can only be connected under BDV!

HVMC 100-1/-2/-3

Datei:HVMC 100-1 Inscription.jpg	Datei:HVMC 100-2 Inscription.jpg	Datei:HVMC 100-3 Inscription.jpg
Print: HVMC 100-1/-2/-3 MDB operation with a Vencube is possible after a software update!

• Software version HVMC 100 Version 1.38 EUR must be used.
• Convert the controller to MDB operation: →Set DIP switch 2 to OPEN.
• Set C8.A with Display Card Amount in the menu.

After replacing the EPROM, the controller must be initialized and reconfigured. All previous data will be lost.

Connecting the Vencube with the MDB Interface

Preparation

1. Disconnect the vending machine control system from the power supply (press the main switch or disconnect ST7).
2. Check the EPROM version:
   HVMC 100-CC Version 1.00 must be replaced with
   HVMC 100-CC Version 1.38!
   Note the installation direction; the notch on the EPROM and IC socket is important, not the EPROM sticker.
3. Insert the Vencube into the MDB interface of the control system.
4. Connect MDB payment systems to the Vencube via MDB.
5. Turn on the vending machine.

Initialize the controller

1. The following display should now appear:
   EPROM swap -> Initialize!
2. Set DIP switches 1 and 5 to the edge of the board and 2-4 to OPEN (controller initialization)!
3. Press the star button
4. The following will appear on the LCD: Clear ??
5. Now press selection button 5 on the machine.
6. Now set all DIP switches to OPEN again.
7. Wait until the display shows Help! F6.
8. Either continue with the section "Switching to a two-line display" or continue with the section "Switching to MDB mode".

Switching to a two-line display

Function of the selection keys in the service menu
Select 1	Back from the submenu
Select 2	Step forward (larger) in the menu
Select 3	Step back (smaller) in the menu
Select 4	Call (enter) the selected menu item
Select 5	Special functions (Delete)	Clear

1. If a two-line display is installed, the display setting must be changed to 2 lines with 16 characters.
   Important: This step can be skipped with a single-line LCD display!
2. Press the star button for more than 5 seconds:
   Clr ERR! appears (keep holding it down)
   and wait for the ServMenu display and release.
   Following: C 0. .
3. Press selection button 2: You will be asked for a password! PW ????
   The password is 4231. Press the corresponding selection buttons and after entering it, the following appears: C 1. .
4. Press selection button 4 and then press selection button 2 several times to go to the menu item C 1.C..
5. Use selection button 4 to call up the setting 1Zl.8St.
   and use selection button 2 to set it to two lines. 2Zl.16St
6. Go back with selection key 1 until C 0. . is displayed.
7. Press the star button
8. Wait until Help! F6 appears on the display.

Switch to MDB operation

1. Activate the MDB credit system: Set DIP switches 1, 3-5 to OPEN and DIP switch 2 to the edge of the circuit board.
2. If necessary, activate the empty lamp control for GP: Set DIP switch 4 to the edge of the circuit board.
3. Press the star button
   After the control unit has booted up, one of the two displays should appear on the display.
   either: No change! or: Hello

Setting the machine

Function of the selection key