G-Drink: Unterschied zwischen den Versionen

Aus Vensolutions
Zur Navigation springen Zur Suche springen
VisuellWikitext
(Die Seite wurde neu angelegt: „{| class="wikitable" |- ! Automatentyp ! Schnittstelle ! Türschalter ! Halterung Türschalter ! Anschlußkabel ! Anschlagwinkel ! Befes…“)
 
Keine Bearbeitungszusammenfassung
 
(23 dazwischenliegende Versionen von 3 Benutzern werden nicht angezeigt)
Zeile 1: Zeile 1:
{| class="wikitable"
== Installation instructions ==
|-
 
! Automatentyp
{{Vorlage:Bedienungsanleitung Vencube beta}}
! Schnittstelle   
 
! Türschalter   
{{Vorlage:Vencube Montage und Inbetriebnahme}}
! Halterung Türschalter
! Anschlußkabel     
! Anschlagwinkel     
! Befestigung Vencube  


   
|-
| G-Drink
| MDB       
| Art.Nr.:22-0745
Doorswitch Cherry 6.3mm Push/pull 
| Art. Nr.: 33-5000-00
Halterung Türschalter 90° 
| Art. Nr.: VTC-X5-IO1-300
Anschlußkabel Türschalter 3000mm               
| nicht erforderlich   
| Verklebt


 
{|
| style="vertical-align:top"|
{{Vorlage:Hinweis Türschalter Installation}}
| style="vertical-align:top"|
[[Datei:einbaulage Vencube klein.jpg|200px|thumb|left|Door inside with door switch]] 
| style="vertical-align:top"|
[[Datei:Türschalter klein.jpg|200px|thumb|left|Door inside]]
|}
|}


{| class="wikitable"
== Machine control board SF01 ==
 
=== Software status of the machine control ===
 
=== Machine control settings ===
 
==== Adjustment of prices ====
 
The sales prices must be set the same for the cash prices and for the card prices(cashless prices).
 
===== Setting the "No Change" Indicator =====
 
Adjust the setting in the "CONFY" menu item for the customer-specific setting under "C2" for determining the tube of the message: "Insert counted money only".
 
;MDB MODE
::If the tubes selected here are empty, "Insert only counted money" will be displayed.
::A = tube with the smallest coin denomination
::D = Tube with the highest coin value
 
If the tubes are empty according to the following configurations, the display will
"Counted money" switched on
 
{| class="wikitable mw-datatable" style="text-align:center" width="40%" border="1"
|-
! width=" 5%" | value
! width="35%" | function
|-
| 0 || Tube A and Tube B and Tube C and Tube D
|-
|-
| '''Ansicht 1'''<br/>
| 1 || Tube A or Tube B or Tube C
[[Datei:Tür innen mit Türschalter klein.jpg|200px|thumb|left|Tür innen mit Türschalter]] 
|-
| '''Ansicht 2'''<br/>
| 2 || Tube A
[[Datei:Tür innen klein.jpg|200px|thumb|left|Tür innen]] 
|-
| '''Ansicht 3'''<br/>
| 3 || Tube B
[[Datei:Anschlagwinkel klein.jpg|200px|thumb|left|Türschalter Anschlag]]
|-
| '''Ansicht 4'''<br/>
| 4 || Tube C
[[Datei:Softwareversion klein.jpg|200px|thumb|left|Softwareversion]]   
|-
| 5 || Tube D
|-
| 6 || Tube B or C or D
|-
| 7 || Tube A and Tube B or Tube C
|-
| 8 || Tube A and Tube B or Tube D
|-
| 9 || Tube A and Tube C or Tube D
|-
| 10 || Tube B and Tube C or Tube D
|-
| 11 || Tube A and Tube D or Tube C
|-
| 12 || Tube B and Tube D or Tube A
|-
| 13 || Tube A or Tube C
|-
| 14 || Tube A or Tube B and Tube C
|-
| 15 || Tube A or Tube B
|}
|}


{| class="wikitable"
After entering the configuration number, save the setting with button 4
 
Set the number of coins in menu item "C03" level for display "Insert counted money only". When the number of coins set here (1 to 10) is reached, the display "Insert counted money only" is switched on. Ideally, 10 coins should be set here.
 
== Machine control board SEV01 ==
 
=== Software status of the machine control ===
 
=== Machine control settings ===
 
==== Adjustment of prices ====
 
The sales prices must be set the same for the cash prices and for the card prices (cashless prices).
 
==== No change display setting ====
 
In the settings menu '''4.1.2.7 "Value for display only cash"''' set to the same value as in Vencube under [[VenToolWin#Program interface:_Coin changer_/_Bank note reader|Limit "No change"]].< br>
If the condition of the change is not met, “ENTER EXACT CHANGE” will appear on the machine display.
 
This function is only taken into account if multiple sales are activated under 4.1.2.5.
 
== Operating instructions of the vending machine ==
 
{| class="wikitable mw-datatable" style="text-align:center" width="60%" border="1"
|-
|-
'''Sonstige Bemerkungen'''
! width="20%" | VMC type
! width="40%" | Operation manual
|-
|-
| '''Softwarestand VMC:''' V5.18 oder höher
| SF01 - G-Drink
'''Hinweis:''' Cashless Preise Einstellen<br/>
| Example
Vencube MDB Level1 mit Aufbuchen<br/>
|-
 
| SVE01 - G-Drink
| Example
|}




Aktuelle Version vom 12. März 2025, 14:04 Uhr

Installation instructions

File User manual Vencube beta currently only in German
Download link BA_Vencube_beta_032020.pdf

Vencube assembly and commissioning

Mount the Vencube

The device is assembled by the customer.
Proceed as follows during assembly:

  • Open the machine.
  • Turn off the power to the machine.
  • Determine the optimal installation position:
    Place the VENCUBE as close as possible to the machine controls and payment systems.
    Make sure that the controls are easily accessible.
    Note the cable length.
  • Glue the base plate (holder) and screw it. (Image 1)

If gluing is not possible, the assembly click holder must be screwed diagonally to the designated points in the machine with at least 2 screws1). The screw heads must be complete Sit flush and must not protrude.
1) Hardened countersunk self-drilling screw, ∅ 3.5 according to DIN 7504

  • Clip the VENCUBE into the base plate. (Image 2)
  • Remove the machine controls cover.

The machine must be voltage-free!

  • Disconnect all existing payment systems (1, 2) from the machine control. (Image 3)
  • Connect the cables from the VENCUBE:
  • Connect the (MDB) master connection (3) from the VENCUBE to the vending machine control. (Image 4)
  • Connect the (MDB) slave port (4) to all existing payment systems (5). If necessary, use a Y-cable. (Image 5)
  • If possible, glue the antenna (6) behind a plastic cover. (Image 6)
  • Route the antenna cable.
  • Lay all cables professionally with cable ties.

Never use the existing door switch of the machine, this can destroy the Vencube.

Always connect the door switch as closer to plug 1 with the Vencube.
Use connector "COM" and connector "NO" from the switch.

Image 1
Image 3
Image 5
Image 2
Image 4
Image 6

Vencube Commissioning

  • Turn on the machine.
  • If necessary, adjust the Vencube using the Ventool.
  • If necessary, configure the machine control and the payment systems.
    You can find information on this in the wiki!
  • Wait until both LEDs turn green.
  • Close the door.
  • Test the machine by making a trial vend with change.
  • Open the door again.
  • Enter the data for VENSOFT (serial number, machine number).
  • Perform a cash withdrawal by pressing the “E” button on the Vencube until you hear a beep.
  • Close the door.
  • Commissioning is complete.


  • Place Vencube as close as possible to the vending machine control and payment systems.
  • Glue or screw the base plate into the machine. If the base plate is glued, please press it firmly into place without the Vencube.
  • Power down the machine and disconnect all existing payment systems from the vending machine control.
  • Connect the MDB master port from the VenCube to the vending machine control.
  • Connect the MDB slave port to all existing payment systems. Y-cables should be used for additional MDB slave connections.
  • Install door switch.

Never use the existing door switch of the machine, this can destroy the Vencube.

Always connect the door switch as closer to plug 1 with the Vencube.
Use connector "COM" and connector "NO" from the switch.

Door inside with door switch
Door inside

Machine control board SF01

Software status of the machine control

Machine control settings

Adjustment of prices

The sales prices must be set the same for the cash prices and for the card prices(cashless prices).

Setting the "No Change" Indicator

Adjust the setting in the "CONFY" menu item for the customer-specific setting under "C2" for determining the tube of the message: "Insert counted money only".

MDB MODE
If the tubes selected here are empty, "Insert only counted money" will be displayed.
A = tube with the smallest coin denomination
D = Tube with the highest coin value

If the tubes are empty according to the following configurations, the display will "Counted money" switched on

value function
0 Tube A and Tube B and Tube C and Tube D
1 Tube A or Tube B or Tube C
2 Tube A
3 Tube B
4 Tube C
5 Tube D
6 Tube B or C or D
7 Tube A and Tube B or Tube C
8 Tube A and Tube B or Tube D
9 Tube A and Tube C or Tube D
10 Tube B and Tube C or Tube D
11 Tube A and Tube D or Tube C
12 Tube B and Tube D or Tube A
13 Tube A or Tube C
14 Tube A or Tube B and Tube C
15 Tube A or Tube B

After entering the configuration number, save the setting with button 4

Set the number of coins in menu item "C03" level for display "Insert counted money only". When the number of coins set here (1 to 10) is reached, the display "Insert counted money only" is switched on. Ideally, 10 coins should be set here.

Machine control board SEV01

Software status of the machine control

Machine control settings

Adjustment of prices

The sales prices must be set the same for the cash prices and for the card prices (cashless prices).

No change display setting

In the settings menu 4.1.2.7 "Value for display only cash" set to the same value as in Vencube under Limit "No change".< br> If the condition of the change is not met, “ENTER EXACT CHANGE” will appear on the machine display.

This function is only taken into account if multiple sales are activated under 4.1.2.5.

Operating instructions of the vending machine

VMC type Operation manual
SF01 - G-Drink Example
SVE01 - G-Drink Example
Abgerufen von „https://wiki.vensoft.de/en/index.php?title=G-Drink&oldid=5574“