Vorlagenübersicht

Vorlagen für Einbauhinweise

Vorlage:Vencube Montage und Inbetriebnahme

Vencube assembly and commissioning

Mount the Vencube

The device is assembled by the customer. Proceed as follows during assembly: Open the machine. Turn off the power to the machine. Determine the optimal installation position: Place the VENCUBE as close as possible to the machine controls and payment systems. Make sure that the controls are easily accessible. Note the cable length. Glue the base plate (holder) and screw it. (Image 1) If gluing is not possible, the assembly click holder must be screwed diagonally to the designated points in the machine with at least 2 screws1). The screw heads must be complete Sit flush and must not protrude. 1) Hardened countersunk self-drilling screw, ∅ 3.5 according to DIN 7504 Clip the VENCUBE into the base plate. (Image 2) Remove the machine controls cover. The machine must be voltage-free! Disconnect all existing payment systems (1, 2) from the machine control. (Image 3) Connect the cables from the VENCUBE: Connect the (MDB) master connection (3) from the VENCUBE to the vending machine control. (Image 4) Connect the (MDB) slave port (4) to all existing payment systems (5). If necessary, use a Y-cable. (Image 5) If possible, glue the antenna (6) behind a plastic cover. (Image 6) Route the antenna cable. Lay all cables professionally with cable ties. Never use the existing door switch of the machine, this can destroy the Vencube. Always connect the door switch as closer to plug 1 with the Vencube. Use connector "COM" and connector "NO" from the switch.

Image 1 Image 3 Image 5

Image 2 Image 4 Image 6

Vencube Commissioning

• Turn on the machine.
• If necessary, adjust the Vencube using the Ventool.
• If necessary, configure the machine control and the payment systems.
  You can find information on this in the wiki!
• Wait until both LEDs turn green.
• Close the door.
• Test the machine by making a trial vend with change.
• Open the door again.
• Enter the data for VENSOFT (serial number, machine number).
• Perform a cash withdrawal by pressing the “E” button on the Vencube until you hear a beep.
• Close the door.
• Commissioning is complete.

Vorlagen für Bedienungsanleitung Vencube

Vorlage:Bedienungsanleitung Vencube alpha
Vorlage:Bedienungsanleitung Vencube alpha

Vorlage:Bedienungsanleitung Vencube beta

File	User manual Vencube beta currently only in German
Download link	BA_Vencube_beta_032020.pdf

Vorlagen für CPI/MEI

mei CF 690 Vencube produces ticking noises

Vorlage:Mei CF 690 VenCube erzeugt tickende Geräusche

image	root cause	rectification
	MDB level from coin changer is not level 3	The coin changer must be converted to MDB Level 3 with all extras: Hold the "Yellow button" on the coin validator for two seconds until Prices appears on the display. Use the "B button" (press once) to go to Settings and confirm with the "A button" . Now the display shows MDB Config.: Active and by pressing the '"A-key" again MDB Version is called up. The display continues to scroll and pressing the "A button" again shows (level). There are three settings: Change with the 'B-key'! - Level 2 - Level 3 No Extras - Level 3 All extras. Select the setting MDB Level 3 All Extras and confirm with the '"A-Key". Exit the settings menu by pressing the "yellow button". If the VenCube is still ticking, the vending machine must be switched off once. Please wait a few seconds before switching it on again. Attention: There are 2x MDB Level 3, please note the running text in the display.

mei CF 7400 Vencube produces ticking noises

Vorlage:Mei CF 7400 VenCube erzeugt tickende Geräusche

image	root cause	rectification
	MDB level from coin changer is not level 3	The CF7400 cannot be switched in the field. In this case, the coinchanger must be replaced.

mei CF 7900 Vencube produces ticking noises

Vorlage:Mei CF 7900 VenCube erzeugt tickende Geräusche

image	root cause	rectification
	MDB level from coin changer is not level 3	Setting Press and hold the yellow button on the coin validator for 3 seconds until Prices is shown on the display. Press the D button 3x until Automation Options appears on the display. Press yellow button 1x for MDB Options and press yellow button again for Change. optimal.. Press the D button once for Level and confirm with the yellow button. Then press the D button until Level 3 is displayed and confirm with yellow. Now press the C button until you exit the menu. Then restart the vending machine. Please wait a few seconds before turning it back on.

mei CF 8000 Vencube produces ticking noises

Vorlage:Mei CF 8000 VenCube erzeugt tickende Geräusche

image	root cause	rectification
	MDB level from coin changer is not level 3	The level 3 setting applies to all four variants of the 8000 series. CF 8200 CF 8250 CF 8500 CF 8550 Setting Press and hold the yellow button on the coin validator for 3 seconds until Prices is shown on the display. Press the D button 3x until Automation Options appears on the display. Press yellow button 1x for MDB Options and press yellow button again for Change. optimal.. Press the D button once until Level is displayed. Select Level menu with yellow and select Level 3 using the D or E button and confirm with yellow. Then press the C button until you exit the menu. Then restart the vending machine. Please wait a few seconds before turning it back on.

Vorlagen NRI

Currenza C² Vencube produces ticking noises

Vorlage:Currenza C2 VenCube erzeugt tickende Geräusche

Image	Root cause	Rectification
	MDB level from coin changer is not level 3	Press menu key. Select button E for settings. Step down with the B button to -Other settings and confirm again with E (OK). Press button B until -MDB-Level- is displayed. Confirm again with E. Now you can change the level with the A and B keys. Level 3 must be set. Confirm with E (OK) and exit the menu with the Menu button (press twice). The vending machine must be switched off and on again once. Please wait a few seconds before turning it back on. If the device does not have a display with buttons, the change can be made with the HENRI module.

Vorlagen für Sielaff

Hinweis erhöter Datenaustausch

Vorlage:Hinweis erhöter Datenaustausch

After the VMC is switched on for the first time with the Vencube connected, there is increased data exchange between the controller and the Vencube. As a result, the VMC cannot be operated for up to ten minutes, or only very slowly, and coin acceptance and payout can be disrupted at the same time. After the waiting time, the machine will work again without any problems.

Hinweise MDB Sielaff

Vorlage:Hinweis MDB Sielaff

Note: These VMC all have MDB interfaces, the Vencube should therefore also be operated directly via MDB without adapter boards or cable harnesses and not via BDV master cable. Depending on which cashless payment system is connected to the Vencube, a BDV or MDB slave cable is to be used here. For coin changers and bill readers, always MDB is preferable.

Hinweise Software Sielaff

Vorlage:Hinweis Software Sielaff

Note: Depending on the type of VMC and the software version of the VMC, not all setting options may be available, and the points that are not available can then be skipped. It may also be possible that the setting items have a German or English name, or that the texts are displayed somewhat differently.

Hinweise Patchmenü Sielaff FKS

Vorlage:Hinweis Patchmenü Sielaff FKS
Make the following settings in the patch menu and check them in the installation menu and make additional settings there if necessary.

The patch menu is reached via the service menu (M-8-E) by entering 99M 55M.

Settings in the patch menu M - 8 - E 99M 55M Menu structure as in FKSEs709 Settings Options ALT.PAYOUT enabled TUBECOUNT COIN MECH contr. MIXED PAYMENT allowed MDB-comp.mode B.Pract. SAVE SETTINGS yes After pressing the "E" key "done" stands for confirmation in the display!

Settings in the installation menu M - 7 - E Menu structure as in FKSEs709 Settings Options > CREDIT SYSTEM CRED. CONFIG. MAN.CONFIG. > COIN MECHANISM TUBE COUNT by COINMECH ALT. PAYOUT on TUBES EMPTY INFO A > CARD READER MIXED PAYM. on MIXED PAYM.PRICE cash price MDB-comp.mode Best Practice

Note: The previously made settings must be checked again after a software update of the VMC.

Hinweise Patchmenü Sielaff FK M32

Vorlage:Hinweis Patchmenü Sielaff FK M32
Make the following settings in the patch menu and check them in the installation menu and make additional settings there if necessary.

The patch menu is reached via the service menu (M-8-E) by entering 99M 55M.

Settings in the patch menu M - 8 - E 99M 55M Menu structure as in FKMEj709 Settings Options ALT.PAYOUT enabled TUBECOUNT COIN MECH contr. MIXED PAYMENT allowed MDB-comp.mode B.Pract. SAVE SETTINGS yes After pressing the "E" key "done" stands for confirmation in the display!

Settings in the installation menu M - 7 - E Menu structure as in FKSMj709 Settings Options > CREDIT SYSTEM CRED. CONFIG. MAN.CONFIG. > COIN MECHANISM TUBE COUNT by COINMECH ALT. PAYOUT on TUBES EMPTY INFO A > CARD READER MIXED PAYM. on MIXED PAYM.PRICE cash price MDB-comp.mode Best Practice

Note: The previously made settings must be checked again after a software update of the VMC.

Hinweise Patchmenü Sielaff HG

Vorlage:Hinweis Patchmenü Sielaff HG
Make the following settings in the patch menu and check them in the installation menu and make additional settings there if necessary.

The patch menu is reached via the service menu (M-8-E) by entering 99M 55M.

Settings in the patch menu M - 8 - E 99M 55M Menu structure as in Settings Options ALT.PAYOUT enabled TUBECOUNT COIN MECH contr. MIXED PAYMENT allowed MDB-comp.mode B.Pract. SAVE SETTINGS yes After pressing the "E" key "done" stands for confirmation in the display!

Settings in the installation menu M - 7 - E Menu structure as in Settings Options > CREDIT SYSTEM CRED. CONFIG. MAN.CONFIG. > COIN MECHANISM TUBE COUNT by COINMECH ALT. PAYOUT on TUBES EMPTY INFO A > CARD READER MIXED PAYM. on MIXED PAYM.PRICE cash price MDB-comp.mode Best Practice

Note: The previously made settings must be checked again after a software update of the VMC.

Hinweise Patchmenü Sielaff HG M32

Vorlage:Hinweis Patchmenü Sielaff HG M32
Make the following settings in the patch menu and check them in the installation menu and make additional settings there if necessary.

The patch menu is reached via the service menu (M-8-E) by entering 99M 55M.

Settings in the patch menu M - 8 - E 99M 55M Menu structure as in Settings Options ALT.PAYOUT enabled TUBECOUNT COIN MECH contr. MIXED PAYMENT allowed MDB-comp.mode B.Pract. SAVE SETTINGS yes After pressing the "E" key "done" stands for confirmation in the display!

Settings in the installation menu M - 7 - E Menu structure as in Settings Options > CREDIT SYSTEM CRED. CONFIG. MAN.CONFIG. > COIN MECHANISM TUBE COUNT by COINMECH ALT. PAYOUT on TUBES EMPTY INFO A > CARD READER MIXED PAYM. on MIXED PAYM.PRICE cash price MDB-comp.mode Best Practice

Note: The previously made settings must be checked again after a software update of the VMC.

Hinweise Softwareupdate Sielaff

Vorlage:Hinweise Patchmenü Sielaff

Note: The previously made settings must be checked again after a software update of the control.

Hinweis Patchmenü Sielaff SÜ

Vorlage:Hinweis Patchmenü Sielaff SÜ ROB
Make the following settings in the patch menu and check them in the installation menu and make additional settings there if necessary.

The patch menu is reached via the service menu (M-8-E) by entering 99M 55M.

Settings in the patch menu M - 8 - E 99M 55M Settings Options ALT.PAYOUT enabled TUBECOUNT COIN MECH contr. MIXED PAYMENT allowed MDB-comp.mode B.Pract. SAVE SETTINGS yes After pressing the "E" key "done" stands for confirmation in the display!

Settings in the installation menu M - 7 - E Settings Options > CREDIT SYSTEM CRED. CONFIG. MAN.CONFIG. > COIN MECHANISM TUBE COUNT by COINMECH ALT. PAYOUT on TUBES EMPTY INFO A > CARD READER MIXED PAYM. on MIXED PAYM.PRICE cash price MDB-comp.mode Best Practice MDB ITEM NUMBERS Hexadezimal

Note: The previously made settings must be checked again after a software update of the VMC.

Hinweis Patchmenü Sielaff SÜ

Vorlage:Hinweis Patchmenü Sielaff SÜ ROB M32
Make the following settings in the patch menu and check them in the installation menu and make additional settings there if necessary.

The patch menu is reached via the service menu (M-8-E) by entering 99M 55M.

Settings in the patch menu M - 8 - E 99M 55M Settings Options ALT.PAYOUT enabled TUBECOUNT COIN MECH contr. MIXED PAYMENT allowed MDB-comp.mode B.Pract. SAVE SETTINGS yes After pressing the "E" key "done" stands for confirmation in the display!

Settings in the installation menu M - 7 - E Settings Options > CREDIT SYSTEM CRED. CONFIG. MAN.CONFIG. > COIN MECHANISM TUBE COUNT by COINMECH ALT. PAYOUT on TUBES EMPTY INFO A > CARD READER MIXED PAYM. on MIXED PAYM.PRICE cash price MDB-comp.mode Best Practice MDB ITEM NUMBERS Hexadezimal

Note: The previously made settings must be checked again after a software update of the VMC.

Hinweis Patchmenü Sielaff SÜ

Vorlage:Hinweis Patchmenü Sielaff SÜ
Make the following settings in the patch menu and check them in the installation menu and make additional settings there if necessary.

The patch menu is reached via the service menu (M-8-E) by entering 99M 55M.

Settings in the patch menu M - 8 - E 99M 55M Settings Options ALT.PAYOUT enabled TUBECOUNT COIN MECH contr. MIXED PAYMENT allowed MDB-comp.mode B.Pract. SAVE SETTINGS yes After pressing the "E" key "done" stands for confirmation in the display!

Settings in the installation menu M - 7 - E Settings Options > CREDIT SYSTEM CRED. CONFIG. MAN.CONFIG. > COIN MECHANISM TUBE COUNT by COINMECH ALT. PAYOUT on TUBES EMPTY INFO A > CARD READER MIXED PAYM. on MIXED PAYM.PRICE cash price MDB-comp.mode Best Practice MDB ITEM NUMBERS Hexadezimal

Note: The previously made settings must be checked again after a software update of the VMC.

Hinweis Patchmenü Sielaff SÜ M32

Vorlage:Hinweis Patchmenü Sielaff SÜ M32
Make the following settings in the patch menu and check them in the installation menu and make additional settings there if necessary.

The patch menu is reached via the service menu (M-8-E) by entering 99M 55M.

Settings in the patch menu M - 8 - E 99M 55M Settings Options ALT.PAYOUT enabled TUBECOUNT COIN MECH contr. MIXED PAYMENT allowed MDB-comp.mode B.Pract. SAVE SETTINGS yes After pressing the "E" key "done" stands for confirmation in the display!

Settings in the installation menu M - 7 - E Settings Options > CREDIT SYSTEM CRED. CONFIG. MAN.CONFIG. > COIN MECHANISM TUBE COUNT by COINMECH ALT. PAYOUT on TUBES EMPTY INFO A > CARD READER MIXED PAYM. on MIXED PAYM.PRICE cash price MDB-comp.mode Best Practice MDB ITEM NUMBERS Hexadezimal

Note: The previously made settings must be checked again after a software update of the VMC.

Vorlagen für Vendo

Hinweis Vendo Cashless Preise Einstellen

Vorlage:Hinweis Vendo Cashless Preise Einstellen
Vorlage:Hinweis Vendo Cashless Preise Einstellen

Vorlagen für Türschalter

Hinweis vorhandener Türschalter

Vorlage:Hinweis vorhandener Türschalter

Never use the existing door switch of the machine, this can destroy the Vencube.

Hinweis Türschalter als Schließer

Vorlage:Hinweis Türschalter als Schließer

Always connect the door switch as closer to plug 1 with the Vencube. Use connector "COM" and connector "NO" from the switch.