SiOne

Aus Vensolutions
Zur Navigation springen Zur Suche springen
Mainpage
Sielaff
FK series
Robimat
Hot drinks vending machine
Stand vending machine
Table Top
Spiral vending machine
Combi vending machine
Bottle return machine

Back to Sielaff overview

Installation instructions

File User manual Vencube beta currently only in German
Download link BA_Vencube_beta_032020.pdf

Vencube assembly and commissioning

Mount the Vencube

The device is assembled by the customer.
Proceed as follows during assembly:

  • Open the machine.
  • Turn off the power to the machine.
  • Determine the optimal installation position:
    Place the VENCUBE as close as possible to the machine controls and payment systems.
    Make sure that the controls are easily accessible.
    Note the cable length.
  • Glue the base plate (holder) and screw it. (Image 1)

If gluing is not possible, the assembly click holder must be screwed diagonally to the designated points in the machine with at least 2 screws1). The screw heads must be complete Sit flush and must not protrude.
1) Hardened countersunk self-drilling screw, ∅ 3.5 according to DIN 7504

  • Clip the VENCUBE into the base plate. (Image 2)
  • Remove the machine controls cover.

The machine must be voltage-free!

  • Disconnect all existing payment systems (1, 2) from the machine control. (Image 3)
  • Connect the cables from the VENCUBE:
  • Connect the (MDB) master connection (3) from the VENCUBE to the vending machine control. (Image 4)
  • Connect the (MDB) slave port (4) to all existing payment systems (5). If necessary, use a Y-cable. (Image 5)
  • If possible, glue the antenna (6) behind a plastic cover. (Image 6)
  • Route the antenna cable.
  • Lay all cables professionally with cable ties.

Never use the existing door switch of the machine, this can destroy the Vencube.

Always connect the door switch as closer to plug 1 with the Vencube.
Use connector "COM" and connector "NO" from the switch.

Image 1
Image 3
Image 5
Image 2
Image 4
Image 6

Vencube Commissioning

  • Turn on the machine.
  • If necessary, adjust the Vencube using the Ventool.
  • If necessary, configure the machine control and the payment systems.
    You can find information on this in the wiki!
  • Wait until both LEDs turn green.
  • Close the door.
  • Test the machine by making a trial vend with change.
  • Open the door again.
  • Enter the data for VENSOFT (serial number, machine number).
  • Perform a cash withdrawal by pressing the “E” button on the Vencube until you hear a beep.
  • Close the door.
  • Commissioning is complete.


  • Place Vencube as close as possible to the vending machine control and payment systems.
  • Glue or screw the base plate into the machine. If the base plate is glued, please press it firmly into place without the Vencube.
  • Power down the machine and disconnect all existing payment systems from the vending machine control.
  • Connect the MDB master port from the VenCube to the vending machine control.
  • Connect the MDB slave port to all existing payment systems. Y-cables should be used for additional MDB slave connections.
  • Install door switch.

Never use the existing door switch of the machine, this can destroy the Vencube.

Always connect the door switch as closer to plug 1 with the Vencube.
Use connector "COM" and connector "NO" from the switch.

Do not stick the VenCube antenna on the cable duct above or in the vicinity of the insertion chute, this will lead to disruptions in the bottle acceptance!

More information:

  • For cashless systems, depending on the manufacturer, an MDS extension must be used.
  • A reed switch (magnetic switch) can also be used as an alternative to the switch. The reed switch should protrude 1-2 mm.
  • Without a cashless system, the MDB slave interface remains unused, which is why LED1 on the VenCube will flash red twice, see Vencube beta user manual.
SiOne exterior view
Metal bracket door switch
Screwed metal bracket door switch
Door switch metal bracket with switch
Interior view with Vencube
Door switch
Door switch counterplate

Software version / FTL

What is behind the software name?

Software status:

  • Versions from 2012 support -Cash Sale- (coin payout)
  • In the case of versions older than version V50Dc613.pat, the aforementioned version must first be installed before a more recent software version can be installed.
  • Software version of the SiOne should be V50Ec617.pat, with other software the machine could pay out the deposit twice.

Check software version:

Action/Enter Shown in the display
Open the machine door 
Please close machine door!
Use the M button to select SERVICE
and confirm with the E button 
SERVICEMODE
"Set the service key!" note. 
Set the service key!
Enter service number 21... 
Enter service number 00
... and confirm with the L button. 
Enter service number 21
The software version is now displayed. 
Software Machine:
V50Ic213.pat
Software FTL suitable omment
V50Dc613.pat ✘ Minimum software status for current software updates
V50Ec617.pat ✘ Preferred software version:
With older software, the machine could pay out the deposit twice!
V50Gc224.pat ✘
V50Ic213.pat ✘
V50Ic329.pat ✘
V50xcxxx.pat

Settings

  • Automatic type: Sielaff RN SiOne with Sielaff control

Settings with Hopper

Settings in the vending machine control
M - 7 - E

up to software version
xxx.pat

from software version
xxx.pat

Coin payment With
Credit system MDB
Wait for booking Yes
Credit mode Always book up
Always Idle Off
Security High
Lottery system 0
VenCube settings with Ventool
Vending machine interface MDB
MDB Level Level 2
CashSale ON (check)
Bottle return YES (check)
Credit system Without credit system
Booking up Without booking up
VenCube Config:
Download

Please open with right click and "Save As"! 

MA5*GW99*2
MA5*GW101*0
MA5*FRA*1
MA5*GW120*1*0*0*2*0*3*0*0
MA5*GW133*1

Settings with hopper and card or chip

Settings in the vending machine control
M - 7 - E
Coin payment With
Credit system MDB
Wait for booking Yes
Credit mode Delivery without a card
Always Idle Off
Security High
Lottery system 0
Vencube settings with Ventool
Program area Function Option
for MDB-card system 		Option
for Vensells CL
vending machine Vending machine interface MDB MDB
MDB Level Level 2 Level 2
Cash Sale ON ON
Bottle return Yes (check) Yes (check)
Credit system Credit system MDB Without
Card system MDB Booking up With Booking up With Booking up
Booking up system MDB booking up Vensells CL booking up
Please open with right click and "Save As"! Vencube Config:
Download
MA5*CDS*1*3*3
MA5*GW99*1
MA5*GW101*1*0*0
MA5*FRA*1
MA5*GW120*1*0*0*2*0*3*0*0
MA5*GW133*1
Vencube Config:
Download
MA5*CDS*3*3*1
MA5*GW99*2
MA5*GW101*1*0*1
MA5*FRA*1
MA5*GW120*1*0*0*2*0*3*0*0
MA5*GW133*1

Settings with card or chip

Settings in the vending machine control
M - 7 - E
Coin payment without
Credit system MDB
Wait for booking Yes
Credit mode Always book up
Always Idle Off
Security High
Lottery system 0


Vencube settings with Ventool
Program area Function Option
for MDB-card system 		Option
for Vensells CL
vending machine Vending machine interface MDB MDB
MDB Level Level 2 Level 2
Cash Sale ON ON
Bottle return Yes (check) Yes (check)
Credit system Credit system MDB Without
Card system MDB Booking up With Booking up With Booking up
Booking up system MDB booking up Vensells CL booking up
Please open with right click and "Save As"! Vencube Config:
Download
MA5*CDS*1*3*3
MA5*GW99*1
MA5*GW101*1*0*0
MA5*FRA*1
MA5*GW120*1*0*0*2*0*3*0*0
MA5*GW133*1
Vencube Config:
Download
MA5*CDS*3*3*1
MA5*GW99*2
MA5*GW101*1*0*1
MA5*FRA*1
MA5*GW120*1*0*0*2*0*3*0*0
MA5*GW133*1
Abgerufen von „https://wiki.vensoft.de/en/index.php?title=SiOne&oldid=5580“