GF99 Combimat: Unterschied zwischen den Versionen

Open the machine.
Turn off the power to the machine.
Determine the optimal installation position:
Place the VENCUBE as close as possible to the machine controls and payment systems.
Make sure that the controls are easily accessible.
Note the cable length.
Glue the base plate (holder) and screw it. (Image 1)

	If gluing is not possible, the assembly click holder must be screwed diagonally to the designated points in the machine with at least 2 screws¹⁾. The screw heads must be complete Sit flush and must not protrude. 1) Hardened countersunk self-drilling screw, ∅ 3.5 according to DIN 7504

Clip the VENCUBE into the base plate. (Image 2)
Remove the machine controls cover.

	The machine must be voltage-free!

Disconnect all existing payment systems (1, 2) from the machine control. (Image 3)
Connect the cables from the VENCUBE:
Connect the (MDB) master connection (3) from the VENCUBE to the vending machine control. (Image 4)
Connect the (MDB) slave port (4) to all existing payment systems (5). If necessary, use a Y-cable. (Image 5)
If possible, glue the antenna (6) behind a plastic cover. (Image 6)
Route the antenna cable.
Lay all cables professionally with cable ties.

	Never use the existing door switch of the machine, this can destroy the Vencube.

	Always connect the door switch as closer to plug 1 with the Vencube. Use connector "COM" and connector "NO" from the switch.

Vencube Commissioning

Turn on the machine.
If necessary, adjust the Vencube using the Ventool.
If necessary, configure the machine control and the payment systems.
You can find information on this in the wiki!
Wait until both LEDs turn green.
Close the door.
Test the machine by making a trial vend with change.
Open the door again.
Enter the data for VENSOFT (serial number, machine number).
Perform a cash withdrawal by pressing the “E” button on the Vencube until you hear a beep.
Close the door.
Commissioning is complete.

Place Vencube as close as possible to the vending machine control and payment systems.
Glue or screw the base plate into the machine. If the base plate is glued, please press it firmly into place without the Vencube.
Power down the machine and disconnect all existing payment systems from the vending machine control.
Connect the MDB master port from the VenCube to the vending machine control.
Connect the MDB slave port to all existing payment systems. Y-cables should be used for additional MDB slave connections.
Install door switch.

	Never use the existing door switch of the machine, this can destroy the Vencube.

	Always connect the door switch as closer to plug 1 with the Vencube. Use connector "COM" and connector "NO" from the switch.

Initial commissioning

	After the VMC is switched on for the first time with the Vencube connected, there is increased data exchange between the controller and the Vencube. As a result, the VMC cannot be operated for up to ten minutes, or only very slowly, and coin acceptance and payout can be disrupted at the same time. After the waiting time, the machine will work again without any problems.

Settings of the VMC

Set selections in cashles menu to "Hex Format", then selections are equal to the product code

VMC Auster SUE

	Note: These VMC all have MDB interfaces, the Vencube should therefore also be operated directly via MDB without adapter boards or cable harnesses and not via BDV master cable. Depending on which cashless payment system is connected to the Vencube, a BDV or MDB slave cable is to be used here. For coin changers and bill readers, always MDB is preferable.

	Note: Depending on the type of VMC and the software version of the VMC, not all setting options may be available, and the points that are not available can then be skipped. It may also be possible that the setting items have a German or English name, or that the texts are displayed somewhat differently.

Make the following settings in the patch menu and check them in the installation menu and make additional settings there if necessary.

The patch menu is reached via the service menu (M-8-E) by entering 99M 55M.

Settings in the patch menu `M - 8 - E 99M 55M`
Settings	Options
ALT.PAYOUT	enabled
TUBECOUNT	COIN MECH contr.
MIXED PAYMENT	allowed
MDB-comp.mode	B.Pract.
SAVE SETTINGS	yes After pressing the "E" key "done" stands for confirmation in the display!

Settings in the installation menu `M - 7 - E`
Settings		Options
> CREDIT SYSTEM	CRED. CONFIG.	MAN.CONFIG.
> COIN MECHANISM	TUBE COUNT	by COINMECH
	ALT. PAYOUT	on
	TUBES EMPTY INFO	A
> CARD READER	MIXED PAYM.	on
	MIXED PAYM.PRICE	cash price
	MDB-comp.mode	Best Practice
MDB ITEM NUMBERS	Hexadezimal

	Note: The previously made settings must be checked again after a software update of the VMC.

Software version / FTL

Display of the software status in the service menu: M - 8 - E - 21 - L

What is behind the software name?

Software	Patch menu	FTL suitable	Comment

VMC Auster SUE M32

	Note: These VMC all have MDB interfaces, the Vencube should therefore also be operated directly via MDB without adapter boards or cable harnesses and not via BDV master cable. Depending on which cashless payment system is connected to the Vencube, a BDV or MDB slave cable is to be used here. For coin changers and bill readers, always MDB is preferable.

	Note: Depending on the type of VMC and the software version of the VMC, not all setting options may be available, and the points that are not available can then be skipped. It may also be possible that the setting items have a German or English name, or that the texts are displayed somewhat differently.

Make the following settings in the patch menu and check them in the installation menu and make additional settings there if necessary.

The patch menu is reached via the service menu (M-8-E) by entering 99M 55M.

Settings in the patch menu `M - 8 - E 99M 55M`
Settings	Options
ALT.PAYOUT	enabled
TUBECOUNT	COIN MECH contr.
MIXED PAYMENT	allowed
MDB-comp.mode	B.Pract.
SAVE SETTINGS	yes After pressing the "E" key "done" stands for confirmation in the display!

Settings in the installation menu `M - 7 - E`
Settings		Options
> CREDIT SYSTEM	CRED. CONFIG.	MAN.CONFIG.
> COIN MECHANISM	TUBE COUNT	by COINMECH
	ALT. PAYOUT	on
	TUBES EMPTY INFO	A
> CARD READER	MIXED PAYM.	on
	MIXED PAYM.PRICE	cash price
	MDB-comp.mode	Best Practice
MDB ITEM NUMBERS	Hexadezimal

	Note: The previously made settings must be checked again after a software update of the VMC.

Software version / FTL

Display of the software status in the service menu: M - 8 - E - 21 - L

What is behind the software name?

Software	Patch menu	FTL suitable	Comment

VMC Auster HG M32

	Note: These VMC all have MDB interfaces, the Vencube should therefore also be operated directly via MDB without adapter boards or cable harnesses and not via BDV master cable. Depending on which cashless payment system is connected to the Vencube, a BDV or MDB slave cable is to be used here. For coin changers and bill readers, always MDB is preferable.

	Note: Depending on the type of VMC and the software version of the VMC, not all setting options may be available, and the points that are not available can then be skipped. It may also be possible that the setting items have a German or English name, or that the texts are displayed somewhat differently.

Make the following settings in the patch menu and check them in the installation menu and make additional settings there if necessary.

The patch menu is reached via the service menu (M-8-E) by entering 99M 55M.

Settings in the patch menu `M - 8 - E 99M 55M`
Settings	Options
ALT.PAYOUT	enabled
TUBECOUNT	COIN MECH contr.
MIXED PAYMENT	allowed
MDB-comp.mode	B.Pract.
SAVE SETTINGS	yes After pressing the "E" key "done" stands for confirmation in the display!

Settings in the installation menu `M - 7 - E`
Settings		Options
> CREDIT SYSTEM	CRED. CONFIG.	MAN.CONFIG.
> COIN MECHANISM	TUBE COUNT	by COINMECH
	ALT. PAYOUT	on
	TUBES EMPTY INFO	A
> CARD READER	MIXED PAYM.	on
	MIXED PAYM.PRICE	cash price
	MDB-comp.mode	Best Practice
MDB ITEM NUMBERS	Hexadezimal

	Note: The previously made settings must be checked again after a software update of the VMC.

Software version / FTL

Display of the software status in the service menu: M - 8 - E - 21 - L

What is behind the software name?

Software	Patch menu	FTL suitable	Comment

Troubleshooting

Overview of the problem solutions

@@ Zeile 1: / Zeile 1: @@
-Zurück zur [[Sielaff|Sielaffübersicht]]
+{{Vorlage:Linkbox Automaten Sielaff}}
-== Einbauanleitung ==
+Back to [[Sielaff|Sielaff overview]]
+== Installation instructions ==
-{| class="wikitable"
+{|
-|-
+| style="vertical-align:top; width:40em"|
-! Türschalter
+{{Vorlage:Bedienungsanleitung Vencube beta}}
-! Halterung Türschalter
+| style="vertical-align:top"|
-! Anschlußkabel
+[[Datei:Robimat Vencube klein.jpg|200px|thumb|right|Installation position Vencube]]
-! Anschlagwinkel
-! Befestigung Vencube
-|-
-| Art.Nr.:22-0745
-Doorswitch Cherry 6.3mm Push/pull
-| Art.Nr.:33-3000-00
-Halterung Türschalter 90°
-| Art. Nr.: VTC-X5-IO1-300
-Anschlußkabel Türschalter 3000mm
-| nicht erforderlich
-| Verklebt
 |}
+{{Vorlage:Vencube Montage und Inbetriebnahme}}
 {|
 | style="vertical-align:top; width:40em"|
-*VenCube möglichst in der Nähe der Automatensteuerung und den Zahlungssystemen platzieren.
+{{Vorlage:Hinweis Türschalter Installation}}
-*Bodenplatte im Automaten verkleben, oder verschrauben. Fals die Bodenplatte Verklebt wird, bitte ohne Vencube die Bodenplatte fest andrücken.
-*Automat spannungsfrei schalten und alle vorhandenen Zahlungssysteme von der Automatensteuerung trennen.
-*MDB-Master Anschluss vom VenCube mit der Steuerung verbinden.
-*MDB-Slave Anschluss mit allen vorhandenen Zahlungssystemen verbinden. Für zusätzliche MDB-Slave Anschlüsse sollten Y-Kabel genutzt werden.
-*Türschalter einbauen.
-{{Vorlage:Hinweis vorhandener Türschalter}}
-{{Vorlage:Hinweis Türschalter als Schließer}}
 | style="vertical-align:top"|
-[[Datei:Robimat Vencube klein.jpg|200px|thumb|right|Einbauposition VenCube]]
+[[Datei:Robimat Vencube klein.jpg|200px|thumb|right|Installation position VenCube]]
-[[Datei:Türschalter_Winkel_Sielaff_CCEP_1.jpg|200px|thumb|right|Türschalter Winkel]]
+[[Datei:Türschalter_Winkel_Sielaff_CCEP_1.jpg|200px|thumb|right|Door switch angle]]
-[[Datei:Türschalter_Winkel_Sielaff_CCEP_3.jpg|200px|thumb|right|Türschalter Winkel mit Schalter]]
+[[Datei:Türschalter_Winkel_Sielaff_CCEP_3.jpg|200px|thumb|right|Door switch angle with switch]]
 | style="vertical-align:top"|
-[[Datei:Türschalter_Winkel_Sielaff_CCEP_4.jpg|200px|thumb|right|Türschalter Winkel eingebaut]]
+[[Datei:Türschalter_Winkel_Sielaff_CCEP_4.jpg|200px|thumb|right|Door switch angle installed]]
-[[Datei:Türschalter_Winkel_Sielaff_CCEP_2.jpg|200px|thumb|right|Türschalter Winkel verschraubt]]
+[[Datei:Türschalter_Winkel_Sielaff_CCEP_2.jpg|200px|thumb|right|Door switch angle screwed]]
 |}
-==Erstinbetriebnahme==
+==Initial commissioning==
 {{Vorlage:Hinweis erhöter Datenaustausch}}
-== Einstellungen der Steuerung ==
+== Settings of the VMC ==
-Anwahlen im Cashlesmenü einstellen auf <code>"Hex Format"</code>, dann sind Anwahlen gleich dem Produktcode
-=== Auster SUE ===
+Set selections in cashles menu to <code>"Hex Format"</code>, then selections are equal to the product code
+=== VMC Auster SUE ===
-{{Vorlage:Hinweis Patchmenü Sielaff SÜ}}
+{{Vorlage:Hinweis MDB Sielaff}}
+{{Vorlage:Hinweis Software Sielaff}}
+{{Vorlage:Hinweis Patchmenü Sielaff SÜ ROB}}
-==== Softwarestand / FTL ====
+==== Software version / FTL ====
-Anzeige des Softwarestandes im Servicemenü: <code>M - 8 - E - 21 - L</code>
+Display of the software status in the service menu: <code>M - 8 - E - 21 - L</code>
-[[Sielaff Softwarebezeichnungen|Was steckt hinter der Softwarebezeichnung?]]
+[[Sielaff software designations|What is behind the software name?]]
 {| class="wikitable mw-datatable" style="text-align:center" width="30%" border="1"
 |-
 ! width="10%" | Software
-! width="10%" | Patchmenü
+! width="10%" | Patch menu
-! width="10%" | FTL geeignet
+! width="10%" | FTL suitable
+! width="10%" | Comment
 |-
-| {{?}} || {{?}} || {{?}}
+| {{?}} || {{?}} || {{?}} ||
 |}
-=== Steuerung Auster SUE M32 ===
+=== VMC Auster SUE M32 ===
+{{Vorlage:Hinweis MDB Sielaff}}
+{{Vorlage:Hinweis Software Sielaff}}
+{{Vorlage:Hinweis Patchmenü Sielaff SÜ ROB M32}}
-{{Vorlage:Hinweis Patchmenü Sielaff SÜ}}
+==== Software version / FTL ====
-==== Softwarestand / FTL ====
+Display of the software status in the service menu: <code>M - 8 - E - 21 - L</code>
-Anzeige des Softwarestandes im Servicemenü: <code>M - 8 - E - 21 - L</code>
+[[Sielaff software designations|What is behind the software name?]]
 {| class="wikitable mw-datatable" style="text-align:center" width="30%" border="1"
 |-
 ! width="10%" | Software
-! width="10%" | Patchmenü
+! width="10%" | Patch menu
-! width="10%" | FTL geeignet
+! width="10%" | FTL suitable
+! width="10%" | Comment
 |-
-| {{?}} || {{?}} || {{?}}
+| {{?}} || {{?}} || {{?}} ||
 |}
-=== Steuerung Auster HG M32 ===
+=== VMC Auster HG M32 ===
+{{Vorlage:Hinweis MDB Sielaff}}
+{{Vorlage:Hinweis Software Sielaff}}
+{{Vorlage:Hinweis Patchmenü Sielaff SÜ ROB M32}}
-{{Vorlage:Hinweis Patchmenü Sielaff SÜ}}
+==== Software version / FTL ====
-==== Softwarestand / FTL ====
+Display of the software status in the service menu: <code>M - 8 - E - 21 - L</code>
-Anzeige des Softwarestandes im Servicemenü: <code>M - 8 - E - 21 - L</code>
+[[Sielaff software designations|What is behind the software name?]]
 {| class="wikitable mw-datatable" style="text-align:center" width="30%" border="1"
 |-
 ! width="10%" | Software
-! width="10%" | Patchmenü
+! width="10%" | Patch menu
-! width="10%" | FTL geeignet
+! width="10%" | FTL suitable
+! width="10%" | Comment
 |-
-| {{?}} || {{?}} || {{?}}
+| {{?}} || {{?}} || {{?}} ||
 |}
-== Problemlösungen ==
+== Troubleshooting ==
-[[Problemlösungen|Übersicht der Problemlösungen]]
+[[Problem solving|Overview of the problem solutions]]
-*[[Problemlösungen#Der Automat gibt kein Wechselgeld aus|Bei Sielaff Automaten erscheint „Bitte Warten“ im Automaten Display und es ist kein Verkauf möglich.]]
+*[[Problem solving#The machine does not give change|With Sielaff machines, "Please wait" appears in the machine display and no sale is possible.]]
-*[[Problemlösungen#Der Automat gibt kein Wechselgeld aus|Der Automat gibt kein Wechselgeld aus.]]
+*[[Problem solving#The vending machine doesn't give change|The vending machine doesn't give change.]]
-*[[Problemlösungen#Keine Münzannahme und keine Wechselgeld Ausgabe bei Sielaff Automaten|Keine Münzannahme und keine Wechselgeld Ausgabe bei Sielaff Automaten.]]
+*[[Problem solving#No coins accepted and no change given out at Sielaff machines|No coins accepted and no change given out at Sielaff machines.]]
 [[Kategorie:Index]]
 [[Kategorie:Sielaff]]

GF99 Combimat: Unterschied zwischen den Versionen

Aktuelle Version vom 12. März 2025, 10:51 Uhr

Inhaltsverzeichnis

Installation instructions