FS 2020

	Mainpage
	Sielaff
	FK series FK series
	Robimat Robimat Robimat XL GF99 Combimat
	Hot drinks vending machine Stand vending machine SielCup Sielissimo Serie SiGusto SiVend HG 20 Trend Table Top Sielissimo TT Serie Siamonie Serie
	Spiral vending machine SUE 2020
	Combi vending machine FS 2020
	Bottle return machine SiOne

Back to Sielaff overview

Installation instructions

File	User manual Vencube beta currently only in German
Download link	BA_Vencube_beta_032020.pdf

Vencube assembly and commissioning

Mount the Vencube

The device is assembled by the customer. Proceed as follows during assembly: Open the machine. Turn off the power to the machine. Determine the optimal installation position: Place the VENCUBE as close as possible to the machine controls and payment systems. Make sure that the controls are easily accessible. Note the cable length. Glue the base plate (holder) and screw it. (Image 1) If gluing is not possible, the assembly click holder must be screwed diagonally to the designated points in the machine with at least 2 screws1). The screw heads must be complete Sit flush and must not protrude. 1) Hardened countersunk self-drilling screw, ∅ 3.5 according to DIN 7504 Clip the VENCUBE into the base plate. (Image 2) Remove the machine controls cover. The machine must be voltage-free! Disconnect all existing payment systems (1, 2) from the machine control. (Image 3) Connect the cables from the VENCUBE: Connect the (MDB) master connection (3) from the VENCUBE to the vending machine control. (Image 4) Connect the (MDB) slave port (4) to all existing payment systems (5). If necessary, use a Y-cable. (Image 5) If possible, glue the antenna (6) behind a plastic cover. (Image 6) Route the antenna cable. Lay all cables professionally with cable ties. Never use the existing door switch of the machine, this can destroy the Vencube. Always connect the door switch as closer to plug 1 with the Vencube. Use connector "COM" and connector "NO" from the switch.

Image 1 Image 3 Image 5

Image 2 Image 4 Image 6

Vencube Commissioning

• Turn on the machine.
• If necessary, adjust the Vencube using the Ventool.
• If necessary, configure the machine control and the payment systems.
  You can find information on this in the wiki!
• Wait until both LEDs turn green.
• Close the door.
• Test the machine by making a trial vend with change.
• Open the door again.
• Enter the data for VENSOFT (serial number, machine number).
• Perform a cash withdrawal by pressing the “E” button on the Vencube until you hear a beep.
• Close the door.
• Commissioning is complete.

Place Vencube as close as possible to the vending machine control and payment systems. Glue or screw the base plate into the machine. If the base plate is glued, please press it firmly into place without the Vencube. Power down the machine and disconnect all existing payment systems from the vending machine control. Connect the MDB master port from the VenCube to the vending machine control. Connect the MDB slave port to all existing payment systems. Y-cables should be used for additional MDB slave connections. Install door switch. Never use the existing door switch of the machine, this can destroy the Vencube. Always connect the door switch as closer to plug 1 with the Vencube. Use connector "COM" and connector "NO" from the switch.

Sielaff FS 2020 Automat Door switch angle Door switch angle with switch

Installation location of the Vencube Screwed angle door switch Built-in door switch angle

Initial commissioning

After the VMC is switched on for the first time with the Vencube connected, there is increased data exchange between the controller and the Vencube. As a result, the VMC cannot be operated for up to ten minutes, or only very slowly, and coin acceptance and payout can be disrupted at the same time. After the waiting time, the machine will work again without any problems.

Settings of the VMC

VMC Auster SUE

Note: These VMC all have MDB interfaces, the Vencube should therefore also be operated directly via MDB without adapter boards or cable harnesses and not via BDV master cable. Depending on which cashless payment system is connected to the Vencube, a BDV or MDB slave cable is to be used here. For coin changers and bill readers, always MDB is preferable.

Note: Depending on the type of VMC and the software version of the VMC, not all setting options may be available, and the points that are not available can then be skipped. It may also be possible that the setting items have a German or English name, or that the texts are displayed somewhat differently.

Make the following settings in the patch menu and check them in the installation menu and make additional settings there if necessary.

The patch menu is reached via the service menu (M-8-E) by entering 99M 55M.

Settings in the patch menu M - 8 - E 99M 55M Settings Options ALT.PAYOUT enabled TUBECOUNT COIN MECH contr. MIXED PAYMENT allowed MDB-comp.mode B.Pract. SAVE SETTINGS yes After pressing the "E" key "done" stands for confirmation in the display!

Settings in the installation menu M - 7 - E Settings Options > CREDIT SYSTEM CRED. CONFIG. MAN.CONFIG. > COIN MECHANISM TUBE COUNT by COINMECH ALT. PAYOUT on TUBES EMPTY INFO A > CARD READER MIXED PAYM. on MIXED PAYM.PRICE cash price MDB-comp.mode Best Practice MDB ITEM NUMBERS Hexadezimal

Note: The previously made settings must be checked again after a software update of the VMC.

Software version / FTL

Display of the software status in the service menu: M - 8 - E - 21 - L

Software	Patch menu	FTL suitable	Comment

VMC Auster SUE M32

Note: These VMC all have MDB interfaces, the Vencube should therefore also be operated directly via MDB without adapter boards or cable harnesses and not via BDV master cable. Depending on which cashless payment system is connected to the Vencube, a BDV or MDB slave cable is to be used here. For coin changers and bill readers, always MDB is preferable.

Note: Depending on the type of VMC and the software version of the VMC, not all setting options may be available, and the points that are not available can then be skipped. It may also be possible that the setting items have a German or English name, or that the texts are displayed somewhat differently.

Make the following settings in the patch menu and check them in the installation menu and make additional settings there if necessary.

The patch menu is reached via the service menu (M-8-E) by entering 99M 55M.

Settings in the patch menu M - 8 - E 99M 55M Settings Options ALT.PAYOUT enabled TUBECOUNT COIN MECH contr. MIXED PAYMENT allowed MDB-comp.mode B.Pract. SAVE SETTINGS yes After pressing the "E" key "done" stands for confirmation in the display!

Settings in the installation menu M - 7 - E Settings Options > CREDIT SYSTEM CRED. CONFIG. MAN.CONFIG. > COIN MECHANISM TUBE COUNT by COINMECH ALT. PAYOUT on TUBES EMPTY INFO A > CARD READER MIXED PAYM. on MIXED PAYM.PRICE cash price MDB-comp.mode Best Practice MDB ITEM NUMBERS Hexadezimal

Note: The previously made settings must be checked again after a software update of the VMC.

Software version / FTL

Display of the software status in the service menu: M - 8 - E - 21 - L

Software	Patch menu	FTL suitable	Comment

Troubleshooting

Overview of the problem solutions

• With Sielaff machines, "Please wait" appears in the machine display and no sale is possible.
• The vending machine doesn't give change.
• No coins accepted and no change given out at Sielaff machines.