The device is assembled by the customer.
Proceed as follows during assembly:
Open the machine.
Turn off the power to the machine.
Determine the optimal installation position: Place the VENCUBE as close as possible to the machine controls and payment systems. Make sure that the controls are easily accessible. Note the cable length.
Glue the base plate (holder) and screw it. (Image 1)
If gluing is not possible, the assembly click holder must be screwed diagonally to the designated points in the machine with at least 2 screws1). The screw heads must be complete
Sit flush and must not protrude. 1) Hardened countersunk self-drilling screw, ∅ 3.5 according to DIN 7504
Clip the VENCUBE into the base plate. (Image 2)
Remove the machine controls cover.
The machine must be voltage-free!
Disconnect all existing payment systems (1, 2) from the machine control. (Image 3)
Connect the cables from the VENCUBE:
Connect the (MDB) master connection (3) from the VENCUBE to the vending machine control. (Image 4)
Connect the (MDB) slave port (4) to all existing payment systems (5). If necessary, use a Y-cable. (Image 5)
If possible, glue the antenna (6) behind a plastic cover. (Image 6)
Route the antenna cable.
Lay all cables professionally with cable ties.
Never use the existing door switch of the machine, this can destroy the Vencube.
Always connect the door switch as closer to plug 1 with the Vencube. Use connector "COM" and connector "NO" from the switch.
Image 1Image 3Image 5
Image 2Image 4Image 6
Vencube Commissioning
Turn on the machine.
If necessary, adjust the Vencube using the Ventool.
If necessary, configure the machine control and the payment systems. You can find information on this in the wiki!
Wait until both LEDs turn green.
Close the door.
Test the machine by making a trial vend with change.
Open the door again.
Enter the data for VENSOFT (serial number, machine number).
Perform a cash withdrawal by pressing the “E” button on the Vencube until you hear a beep.
Close the door.
Commissioning is complete.
Do not stick the VenCube antenna on the cable duct above or in the vicinity of the insertion chute, this will lead to disruptions in the bottle acceptance!
Other notes:
For cashless systems, depending on the manufacturer, an MDS extension must be used.
A reed switch (magnetic switch) can also be used as an alternative to the switch. The reed switch should protrude 1-2 mm.
Without a cashless system, the MDB slave interface remains unused, which is why LED1 on the VenCube will flash red twice, see Vencube beta Bedienungsanleitung.
SiOne exterior viewInterior view with Vencube
Metal bracket door switchScrewed metal bracket door switchDoor switch metal bracket with switch
Versions from 2012 support -Cash Sale- (coin payout)
In the case of versions older than version V50Dc613.pat, the aforementioned version must first be installed before a more recent software version can be installed.
Software version of the SiOne should be V50Ec617.pat, with other software the machine could pay out the deposit twice.
Check software version:
Action/Enter
Shown in the display
Open the machine door
Please close machine door!
Use the M button to select SERVICE and confirm with the E button
SERVICEMODE
"Set the service key!" note.
Set the service key!
Enter service number 21...
Enter service number 00
... and confirm with the L button.
Enter service number 21
The software version is now displayed.
Software Machine: V50Ic213.pat
Software
FTL suitable
omment
V50Dc613.pat
Mindestsoftwarestand für aktuelle Softwareupdates
V50Ec617.pat
Bevorzugter Softwarestand: Mit älterer Software könnte der Automat zweimal das Pfandgeld auszahlen!
V50Gc224.pat
V50Ic213.pat
V50Ic329.pat
V50xcxxx.pat
Einstellungen der Steuerung
Automatentyp: Sielaff RN SiOne mit Sielaff-Steuerung
